top of page

Cantilever Walls - Unsupported Excavations

Cantilever Excavations

Cantilever walls are walls that do not have any supports and thus lead to an open unobstructed excavation. Cantilever walls laterally restrain the retained side of the excavation by the passive resistance provided below the excavation depth.

Many engineers use the cantilever wall term to actually describe gravity walls. In reality both gravity and vertical embedded walls types can be categorized as cantilever if no lateral bracing support is provided by means of tiebacks, struts, etc.

This sections examines vertical cantilever walls and the basic design methods used for cantilever wall analysis.

In general, the maximum excavation for a cantilever wall can reach up to 6m or 18ft. Deeper cantilever walls have been constructed in the past, but these require more expensive wall systems such as T-type diaphragm walls. Cantilever walls offer some advantages:

Fig: A Cantilever Excavation Analyzed with DeepEX Software

Advantages of cantilever walls:

  • Cantilever walls offer an unobstructed open excavation.

  • Cantilever walls do not require installation of tiebacks below adjacent properties.

  • Cantilever walls offer a simpler staged construction procedure.

Disadvantages of cantilever walls:

  • Maximum excavation for cantilever walls is rather limited, typically to 18 ft (6m) maximum.

  • It is generally not recommended to use cantilever walls next to adjacent buildings.

  • Control of lateral wall displacements depends on the mobilization of passive earth resistance.

  • For deeper cantilever excavations the wall stiffness may need to be considerably increased. This can limit the available space within the excavation.

Cantilever Excavations can be designed in seconds with DeepEX Software! Review Software Capabilities

Analysis methods for cantilever walls:

Cantilever walls are usually analyzed with the limit equilibrium method. In this approach, the designer calculates the active and passive earth pressures on both sides of the wall. Water and other surcharges are also applied if applicable. Two methods in Limit Equilibrium analysis are available:

a) Free earth method for cantilever walls:

This is the simplest approach. It requires that the designer only balances the overturning and resisting moments. Active earth pressures are assumed on the retained side and passive earth pressures are typically assumed on the excavation side. The required embedment for a safety factor of 1 is then obtained at the point of zero moment. The limitation of the method is that shear forces are not balanced. As a result, it is recommended that the obtained embedment for FS=1 is multiplied by approximately 1.2 (to obtain the wall embedment for a safety factor of 1).

b) Fixed earth method for cantilever walls:

The fixed earth method offers a more robust approach as it balances both overturning moments and shears. However, analytical solutions for the fixed earth method are limited to very special conditions. The fixed earth method works by finding the critical pivot point about which rotational moments and shear forces balance. This is done by assuming active earth pressures on the excavation side and passive earth pressures on the retained side below the pivot point. Since closed form solutions with the fixed earth method are limited it is recommended that a Winkler spring analysis will typically offer the best results instead of the classical fixed earth solution.

c) Practical recommendations for cantilever walls

To obtain an adequately safe design, the wall embedment typically required in cantilever walls is in the order of 1.5 times the excavation height. While cantilever walls offer the advantage of an easy excavation the typical maximum depths are in the order of 15 ft or (4.5m). Beyond that depth, stiffer less economical wall sections will be required to limit horizontal wall displacements to tolerable limits. Whie deeper cantilever walls have been successfully used with small sections, their success was often the result of higher observed soil strengths in the field when compared to the conservative design values. Horizontal wall movements should be monitored when constructing deeper cantilever walls.

Video: Cantilever Excavations - Methods and options in DeepEX Software:

Training Example - A Cantilever Sheet Pile Wall Designed with DeepEX:

Cantilever Sheet Pile Wall


Book A free web presentation:

Learn what our program can do for you! Save time and effort!



bottom of page