Tel: 1-206-279-3300

2-Day Deep Excavation Workshop

16 PDH @ New York University

June 6-7, 2019

Early registration ends soon!

DeepEX 2019 is here!

Deep Excavation Software

DeepEX 2017 talk to it and design your deep excavation!

Excavations in 3D, VR, AR

Holographic model of a deep excavation with HoloDeepEX

Get the Free 3D Viewer

______________________

Free 45 min webinar

Deep Excavation Design

Fully booked!

Free Helical Pile Design Webinars:

To be announced

New Deep Foundation Software

DeepFND - Deep Foundation Software, caissons, CFA, drilled piles, driven piles, concrete, timber

 

New helical pile software HelixPile
Signup for a free trial and get our free pdf on the five most common errors in deep excavation design
Our Software Solutions
DeepFND 2020: Deep Foundation software (NEW: Pile-Group/Pile Raft Analysis!)
DeepEX 2019: Deep Excavation software
Soldier pile walls
Sheet pile walls
Secant pile Walls
Tangent piles
Diaphragm Walls
Soldier and Tremied Concrete
Soil Mix walls
Combined king pile sheet piles
Slope stability
Cost estimation for braced excavations
Waler-Strut Cofferdams
Snail-Plus 2019: Soil nailing - soil nailing walls
SiteMaster: Inclinometer software (adopted by Geokon)
HelixPile: Helical Pile Software
RC-Solver: Concrete Design ACI-318, EC2, EC8
Steel-Beam: Steel beam column design, full equations, AISC, EC3

An independent deep excavation analysis model for the repair shaft of the Seattle Viaduct (14/Jan/2015)

The repair works for the Seattle Viaduct (Bertha) have been again on the news. Fox news pointed out to a "draft" report by an engineering firm that used words as catastrophic failure (here is the article). The final report used different language, but the press always wants to jump on anything that sounds scary. We wanted to check the circular shaft with our deep excavation software DeepEX and see if we could find something that raises an alarm.

Seattle Viaduct Repair Access Shaft Jan/14/15

Seattle Viaduct Access Shaft Jan/14/15 (Official Project Website)

First, a little background for those unaware with the story:

Bertha, the tunnel boring machine for the viaduct has been stuck/damaged for the last few months. As part of the repair works, a circular shaft approximately 83ft in diameter and 120 ft deep when finally excavated was proposed and is being constructed. From information that we could extract from the web, the shaft was constructed with large diameter piles (10ft) that are overlapping. It is also our understanding that additional grouting is taking place to create a sufficient compression ring where the large diameter piles have to be constructed next to what appears to be protection piles along the tunnel allignment. Where the tunnel is to bore through, the shaft thickness has been extended with more overlapping pile rows so that increased arching is available.

While we are missing some geotechnical and structural information, we made a series of rough but conservative assumptions for soil properties, water levels, and structural properties to analyze the circular shaft. Some rough geotechnical section could be assumed since the geotechnical baseline report is available online (close to Main Street on map):

Fill for 15ft

Soft clay/silt to 80ft depth

Hard glacial overconsolidated deposits below 80ft

Hydrostatic water pressures are assumed starting from a 10ft depth

Geotechnical section for Seattle Viaduct based on Geotechnical Baseline report by Shannon & Wilson

Geotechnical section for Seattle Viaduct based on Geotechnical Baseline report by Shannon & Wilson (available online)

Based on these assumptions, and using the circular shaft analysis capabilities in DeepEX, we came back with maximum hoop force of 529 k/ft (vertical foot). With an assumption of 1% verticallity tolerance, equivalent compression stresses in the order of 704 psi were computed. We believe that these stresses well within the capacity of the used structural concrete and grout. A more detailed analysis would be required to consider the effects of the openings with rings, but:

a) We need to have all the data

b) We cannot give out such a freebie. If they need it, they can call us.

While our analysis is "preliminary" with rough assumptions, it indicates that the current shaft design appears to be stable and functional.

Concept for removing Bertha with Circular shaft excavation

Image for pile layout for Seattle Viaduct Repair Access Shaft

Image for pile layout for Seattle Viaduct Repair Access Shaft (available from project website)

Model of circular shaft for Seattle Viaduct Repair Access shaft with DeepEX deep excavation software

Model of circular shaft for Seattle Viaduct Repair Access shaft with DeepEX deep excavation software

Want to find out more about DeepEX?

Please check this page and sign up.

DeepEX Pricing

The most complete solution for deep excavations!

More than 10000 projects designed worldwide!

DeepEX

DeepEX 2D: $3,475.00
DeepEX 2D Plus (DeepEX 2D + DXF Drawings): $4,425.00
DeepEX 3D (DeepEX 2D + Cost+Frame+HoloDeepEX): $5,725.00
DeepEX+Cost+Frame+HoloDeepEX
DeepEX 3D Plus (DeepEX3D + DXF Drawings): $6,675.00
DeepEX 3D+ DXF + Gravity Walls
DeepEX 3D Advanced (DeepEX 3D+ Building Damage Module): $8,175.00
Platinum = 3D+ Building Damag